I have the information for the suspension alignment with standard springs, but are there any significant adjustments, or worse still, major problems when running lower/updated springs?
Of course, this is a 1990 V8.
Bearbeitet von Mark
Suspension geometry with lower springs/ride height
23 Beiträge · 15.838 Aufrufe · gestartet
All told me, it's no really need for other adjustments then the "king pin angle" (???), at the most it's not a lot clearance, so they adjust on block.
Hmmm.... I'm not quite sure what that's referring to.
At the back, there is scope for quite a lot of adjustment, and especially getting the camber right.
At the front there is not a lot of scope for camber adjustment on the V8, as the top mounts are at full outboard position, and still with too much camber when loaded.
The bottom location is pretty well not adjustable, without making a completely new track arm, with the bottom ball joint moved inboard. Maybe that is what is referred to, but no such item exists. Maybe I could make some inner track arm mounts with an offset hole?
I think I shall revert to standard springs for a while.
At the back, there is scope for quite a lot of adjustment, and especially getting the camber right.
At the front there is not a lot of scope for camber adjustment on the V8, as the top mounts are at full outboard position, and still with too much camber when loaded.
The bottom location is pretty well not adjustable, without making a completely new track arm, with the bottom ball joint moved inboard. Maybe that is what is referred to, but no such item exists. Maybe I could make some inner track arm mounts with an offset hole?
I think I shall revert to standard springs for a while.
If you don't have problems with steering and the tires don't run flat unsymmetrically, f*ck the adjustments if it's not realisable with original parts... you are just a bit to picky 
No, it's obviously asymmetric wear.
HOW MUCH low is it? just for ice? peppelstones kill your front bumper?
Normally there are no obviousnesses by 35mm lower. I mean, since years my tires run flat outside - not inside (I drive, not sleep by drive) , so there are really no problems with the camber in this way... the guys by the wheel alignment say all the same: it's not quite by rules, but no problem.
Gruess Roy
Actual figures? I don't know. The coils came from one of the companies that advertise on audiv8.
I'm going to go back to standard springs and think again. What springs did you use, Roy?
I'm going to go back to standard springs and think again. What springs did you use, Roy?
R.I.P Eibach 35mm (broken)
Actually H&R 35mm I suppose.
Both didn't brought problems with the geometric measurements to me.
I think you use the one from Frank Ziehm? The speciality in his set are the rear-springs, they are some kind of "heavy duty", normal springs seems to be a bit to slack.
I don't know what, but something is strange with your car....
Actually H&R 35mm I suppose.
Both didn't brought problems with the geometric measurements to me.
I think you use the one from Frank Ziehm? The speciality in his set are the rear-springs, they are some kind of "heavy duty", normal springs seems to be a bit to slack.
I don't know what, but something is strange with your car....
I've been wondering just that.
First, yes these springs are more aggressive. While the rear is nice, the front may be a little low. These springs say a -55mm, but given that others had been using them, there was nothing to worry me.
That said- i had some very serious doubts about the care of the car when it was with the body shop in 2012. 2 years prior, with no issues with the car at all, and then 3 months to scrap a set of tyres.
But I'd then been running these new tyres with even and predictable wear with standard spec suspension and budget front dampers, with no issues. Then I fit new springs, Koni dampers, and a full alignment with no issues.
I'm away for several months, car in storage, then MOTd, and while the tracking may have shifted slightly, not badly. All of a sudden, wedge tyre wear, in the same manner as the previous occasion in 2012.
I've got replacement suspension components to get powder coated to tidy up the rear. The HR are massively expensive here in the UK. equivalent to €450+ for 4 springs.
I'd rather have a little more travel, so for now it seems that back to standard springs are in order.
First, yes these springs are more aggressive. While the rear is nice, the front may be a little low. These springs say a -55mm, but given that others had been using them, there was nothing to worry me.
That said- i had some very serious doubts about the care of the car when it was with the body shop in 2012. 2 years prior, with no issues with the car at all, and then 3 months to scrap a set of tyres.
But I'd then been running these new tyres with even and predictable wear with standard spec suspension and budget front dampers, with no issues. Then I fit new springs, Koni dampers, and a full alignment with no issues.
I'm away for several months, car in storage, then MOTd, and while the tracking may have shifted slightly, not badly. All of a sudden, wedge tyre wear, in the same manner as the previous occasion in 2012.
I've got replacement suspension components to get powder coated to tidy up the rear. The HR are massively expensive here in the UK. equivalent to €450+ for 4 springs.
I'd rather have a little more travel, so for now it seems that back to standard springs are in order.
I'm fitting H&R springs this weekend. I already have Koni Adjustable dampers fitted.
Although it's subjective, are there any suggestions for setting the Dampers, from folks with a Koni and H&R setup?
Although it's subjective, are there any suggestions for setting the Dampers, from folks with a Koni and H&R setup?
Well, this is irritating. The new H&R coils are too big. Outside diameter is too large, and the result is the springs interfere with the camber link on the rear hub.
Has anyone experienced this before?
Has anyone experienced this before?
Do you mean that? : [Bild]http://www.audiv8.com/forum/download.php?Number=359939[/Bild] copy and paste.
Bearbeitet von Tim
well, your link won't....link.
The cause of my problem is hamfistedness. Mine, largely. In my defence, the weather has been utter shite, even by UK standards. But it did highlight a small problem or two. The transverse link, and the bottom connection to one of the dampers is bent. (On the hub assembly)
The main issue being the transverse link that was replaced a little while back. The pin end is massive! So the new springs which are a fraction larger diameter than the KAWs were rubbing the link, just, because of the bottom damper location. Fixed now.
It's all back together now. Time to test drive...
The cause of my problem is hamfistedness. Mine, largely. In my defence, the weather has been utter shite, even by UK standards. But it did highlight a small problem or two. The transverse link, and the bottom connection to one of the dampers is bent. (On the hub assembly)
The main issue being the transverse link that was replaced a little while back. The pin end is massive! So the new springs which are a fraction larger diameter than the KAWs were rubbing the link, just, because of the bottom damper location. Fixed now.
It's all back together now. Time to test drive...
http://www.audiv8.com/forum/showthreaded.php?Cat=&Board=v8forum_ger&Number=359939&page=0&view=collapsed&sb=5&o=&fpart=1
Click the attachment (Anhang).
How did you fix it?
Click the attachment (Anhang).
How did you fix it?
I'm not entirely sure that I have yet. I'll let you know in a few days.
Orientation of the spring is critical, which doesn't immediately make sense. it still has to travel through the normal range of movement.
The head (pin end) of the right hand transverse link seems much larger than the left side. I can't remember where it was sourced from. It also appears to sit further up from the subframe than the other side.
I've run out of time now, so it'll be a week or two before i really know.
By then, I may well be into doing the full rear axle refurb with the spare set of components. I'm adding rear anti roll bar.
Orientation of the spring is critical, which doesn't immediately make sense. it still has to travel through the normal range of movement.
The head (pin end) of the right hand transverse link seems much larger than the left side. I can't remember where it was sourced from. It also appears to sit further up from the subframe than the other side.
I've run out of time now, so it'll be a week or two before i really know.
By then, I may well be into doing the full rear axle refurb with the spare set of components. I'm adding rear anti roll bar.
Bearbeitet von Mark
Mitreden, Fotos sehen und Fragen stellen? Melde dich mit deinem Forum-Zugang an.
Anmelden